Gear Beginner

Your first audio interface: what the specs really mean

Inputs, outputs, sample rate, bit depth and latency — explained in plain language for first-time buyers.

Short answer

For a first interface: get two inputs (one mic, one instrument), 48V phantom power (for condenser microphones), USB connectivity, and drivers with low latency. Record at 44.1 kHz / 24-bit. Sample rate above 44.1 kHz and inputs above 2 are for later. Focusrite Scarlett, Universal Audio Volt and PreSonus AudioBox are the most consistently recommended entry-level options.

What an audio interface does

An audio interface is an analogue-to-digital converter (ADC) and digital-to-analogue converter (DAC) in one box. When you plug a microphone or instrument into it, the interface converts the analogue electrical signal to a stream of digital numbers that your DAW can record. When your DAW plays back, the interface converts those numbers back to an analogue signal for your headphones or monitors.

Compared to a computer's built-in audio chip, a dedicated interface provides: lower latency, higher-quality conversion, proper microphone preamps with phantom power, and balanced outputs that reject electrical noise. These differences are not subtle in a recording context.

Inputs: how many, what type

Inputs on an audio interface are either combo jacks (accepting both XLR microphone cables and 6.35mm instrument cables) or dedicated XLR or instrument inputs. Most entry-level interfaces have two combo inputs, which gives you one microphone and one instrument simultaneously.

Line-level inputs (for connecting synthesisers, keyboards or effects units) accept a different signal level than microphone or instrument inputs. Check whether the interface has a switch between instrument (Hi-Z) and line level — plugging a line-level source into an instrument input (or vice versa) results in distorted or very quiet recordings.

Sample rate and bit depth

Sample rate (measured in kHz) is how many times per second the ADC takes a measurement of the audio. The Nyquist theorem states that the highest reproducible frequency is half the sample rate. At 44.1 kHz, frequencies up to 22.05 kHz are reproduced — well above human hearing (typically 20 Hz – 20 kHz as defined in ISO 226).

Bit depth (16-bit, 24-bit, 32-bit float) determines the dynamic range of the recording. 24-bit gives 144 dB of theoretical dynamic range — far more than any real-world microphone or instrument produces. It means you can record at conservative levels with plenty of headroom without noise becoming a problem.

Record at 44.1 kHz / 24-bit. This is the professional standard for music. Higher sample rates use more storage and may cause clicks or dropouts on less powerful computers if the buffer size is set too low.

Latency and buffer size

Latency is the time between a sound entering the interface and reaching your headphones — caused by the computer processing audio in small chunks called the buffer. A larger buffer reduces CPU dropouts but increases latency; a smaller buffer reduces latency but requires more processing power.

For most recording, set the buffer to 128 or 256 samples (2–6 ms at 44.1 kHz). Some interfaces offer direct monitoring — routing the input signal directly to the headphones in analogue, bypassing the computer entirely. This gives zero-latency monitoring regardless of buffer size, which is useful when recording vocals or instruments through effects.

Preamps and gain

A microphone produces a very small electrical signal — too quiet to record directly. The interface's built-in preamp amplifies it to a recordable level. The gain knob controls how much amplification is applied.

Aim for peaks around –12 dB to –6 dB on the input meter. This leaves headroom for unexpected louder moments without clipping (digital distortion from exceeding 0 dBFS). Recording too quietly (below –24 dB on average) introduces noise when the signal is turned up in the mix.

What to look for when buying

  • USB bus-powered — no separate power supply needed; works directly from your computer
  • Two combo inputs (XLR + 1/4″) — covers microphone and instrument simultaneously
  • 48V phantom power — required for condenser microphones
  • Headphone output with independent volume — essential for monitoring while recording
  • ASIO drivers (Windows) or Core Audio (Mac) — required for low-latency recording; check the manufacturer's driver support before buying
  • Bundled DAW or plugins — most entry-level interfaces include software worth using

Independent reviews from Sound On Sound and Sweetwater cover most interfaces in depth with measurements and real-world use assessments. MusicRadar also publishes buyer's guides comparing interfaces across price brackets. For second-hand interfaces, Reverb is the leading marketplace for used music gear with price history data that helps you assess fair value.

Next step

With an interface set up and working, the next step is understanding the full home studio picture — what else you need and in what order to acquire it. Setting up a home studio: what you need first covers the complete beginner setup including DAW choice, headphone selection and acoustic treatment. Once you are recording, EQ basics is the most immediately useful production skill to develop.

Frequently asked questions