EQ basics: making room for every instrument
What an equaliser does and how to use it so each part of a mix stops masking the others.
Short answer
An equaliser (EQ) boosts or cuts specific frequency ranges. Use it to remove problem frequencies, separate instruments that clash, and give each element of a mix its own space to be heard clearly. Cut first; boost sparingly.
What EQ does
Every sound is a mixture of frequencies. A guitar chord contains a fundamental note, its harmonics, and the noise of the pick or fingers. An EQ divides this spectrum into bands and lets you turn each band up or down independently.
Unlike a volume fader — which makes everything louder or quieter — an EQ changes the shape of the sound. You can make a voice sound warmer, a snare sound snappier, or a bass less muddy, all without touching the overall level.
Use the Note to Frequency tool to convert any note to its Hz value — this helps you find exactly which frequency range an instrument occupies before reaching for an EQ band.
Band types
- High-pass filter (HPF / low-cut): removes everything below a set frequency. Used on most instruments to clean up rumble and mud.
- Low-pass filter (LPF / high-cut): removes everything above a set frequency. Used to soften harshness or remove high-frequency noise.
- Bell (peak/dip): boosts or cuts a frequency range centred on a selected frequency. Q (or bandwidth) controls how narrow or wide the affected range is.
- Shelf: boosts or cuts all frequencies above (high shelf) or below (low shelf) a chosen point. Gentler and more musical-sounding than a steep filter for tonal shaping.
Frequency ranges (approximate)
These are general starting points, not rules. Always listen and adjust to the specific recording.
- Sub-bass (20–80 Hz): felt more than heard. Kick drum weight, bass fundamentals. Too much causes muddiness.
- Bass (80–300 Hz): bass guitar, kick body, lower vocals. The most common source of mix mud.
- Low-mid (300 Hz–1 kHz): warmth and body, but also boxiness and nasality.
- Mid (1–4 kHz): presence, attack, intelligibility. Very sensitive to ear fatigue.
- High-mid (4–8 kHz): harshness, sibilance, clarity or edge depending on how it is handled.
- Air (8–20 kHz): shimmer, openness. Gentle boosts here add brightness without harshness.
Masking and how to fix it
Frequency masking occurs when two sounds occupy the same frequency range. The louder one drowns out the quieter one even though both are audible individually. Common clashes: kick drum and bass guitar, piano and guitar, vocals and synth pads.
The fix is called complementary EQ: if you boost the bass at 200 Hz, cut the kick at 200 Hz by a similar amount, and vice versa. Each instrument still has energy at that frequency, but they no longer directly compete — the kick is louder in the range where the bass is cut, and the bass is louder in the range where the kick is cut.
Before EQing, solo the track and identify the problem frequency by slowly sweeping a narrow bell boost while listening. Once you hear the problem ring out, cut it rather than boost it. Your ears will thank you.
A basic EQ workflow
- Apply a high-pass filter to every track except bass and kick. Start around 80–120 Hz; raise it until the tone starts to thin, then back off slightly.
- Find and cut problem frequencies (mud, boxiness, harshness) on each track.
- Check the mix — do any two elements clash? Apply complementary cuts and boosts.
- Add tonal boosts last, where they genuinely improve the character of the sound rather than just making it louder.
Next step
EQ controls the frequency content of a signal; compression controls its dynamic range (the difference between the loudest and quietest moments). Together they form the foundation of a working mix. The frequency glossary entry gives a plain-language definition you can link back to when reading other production guides. For in-depth EQ technique from professional engineers, Sound On Sound's production techniques library contains hundreds of articles on EQ decisions in context, covering everything from gentle tonal shaping to surgical problem-solving. iZotope\u2019s EQ guides provide visual, interactive explanations of frequency concepts alongside their processing tools.
Frequently asked questions
An equaliser (EQ) lets you boost or cut the volume of specific frequency ranges within a sound. Rather than making a signal louder or quieter overall, it changes the tonal balance — more bass, less high-mid harshness, and so on.
Masking happens when two sounds occupy the same frequency range at similar volumes. The louder sound makes the quieter one hard or impossible to hear, even though both are playing. EQ is used to carve space so each element can be heard clearly.
Cutting is generally preferred for problem-solving (removing mud, harshness or boxiness), while boosting is used to enhance character. Cutting first — removing what you do not want — typically gives cleaner results than stacking boosts.
They are the same thing. A high-pass filter passes high frequencies and cuts (attenuates) low frequencies below its cutoff point. "Low-cut" describes what it removes; "high-pass" describes what it lets through.
Bass guitar fundamentals typically sit between 40 Hz and 300 Hz, with harmonics extending higher. The attack click of a bass note can reach 700 Hz–1 kHz. EQ decisions depend on the specific instrument and recording, so use the Note to Frequency tool to find the exact frequencies of the notes you are working with.
The Note to Frequency tool converts a note name to its fundamental frequency in Hz. If you know a bass guitar is playing a low E (41 Hz), you can set your EQ's low-cut filter just below that to remove rumble without affecting the note.
Sound On Sound's "Mixing Secrets for the Small Studio" series at soundonsound.com covers EQ in the context of real mixing decisions — particularly frequency clashing, high-pass filtering, and surgical cuts. Their Studio SOS articles document real-world mix problems and solutions, making them excellent case studies for how EQ and masking work in practice.